tag:blogger.com,1999:blog-2807403883562053852.post7540967287447936098..comments2024-03-27T08:40:31.785-06:00Comments on Clayton Cramer.: Regular Handgun CleaningClayton Cramerhttp://www.blogger.com/profile/03258083387204776812noreply@blogger.comBlogger4125tag:blogger.com,1999:blog-2807403883562053852.post-44773204714599305822017-08-12T00:38:16.214-06:002017-08-12T00:38:16.214-06:00Clayton,
One of the changes made to the 1911 to cr...Clayton,<br />One of the changes made to the 1911 to create the 1911-A1 version was to radius the firing pin stop plate bottom edge. The original version used the hammer spring as a major part of the slide retardation, by having to move the hammer with little leverage. That, of course, makes it difficult to rack the slide with the hammer down. <br /><br />Empty chamber with hammer down became the Army mandated carry method, and cocking the hammer separately prior to racking the slide was slow and awkward for the average soldier. So, they made racking with the hammer down an easier chore.<br /><br />I would not be surprised if the High Power still had the JMB square corner design. (Supposedly, the felt recoil of the 1911 is easier to control than the 1911-A1. Less rise and twist. Swapping that plate is planned for my .45, one of these days...)Willhttps://www.blogger.com/profile/00722792638246578812noreply@blogger.comtag:blogger.com,1999:blog-2807403883562053852.post-3623826781711525592017-08-11T10:39:28.404-06:002017-08-11T10:39:28.404-06:00I've found that by using Tetra Spray on all th...I've found that by using Tetra Spray on <i>all</i> the metal parts of my 1911s after degreasing, then Tetra Grease for everything but where penetration is needed like the disconnector and magazine release spring (where I use Tetra Oil :-), they will function reliably for <i>years</i>, even with firing a "few" rounds or more of Sellier & Bellot FMJ or Gold Dot. If you're in a really dusty place this might not be a good idea (I've read grease + dust can be a bad combination), and I would certainly clean mine more often if getting range time for test firing wasn't so difficult, but so far this has approach has worked flawlessly for me, with modern reasonably tight guns from or with reliability jobs by Wilson.ThatWouldBeTellinghttps://www.blogger.com/profile/16910231314995266781noreply@blogger.comtag:blogger.com,1999:blog-2807403883562053852.post-50324298639219670942017-08-11T04:15:07.277-06:002017-08-11T04:15:07.277-06:00Jim: Cocking it with hammer down is a real struggl...Jim: Cocking it with hammer down is a real struggle for me since the stroke. I prefer carrying pistols hammer down with a round chambered, and cocking it with my thumb. The BHP is quite a struggle to cock by hand. Not sure why the BHP is more of a struggle than the other 1911 variants that I own.Clayton Cramerhttps://www.blogger.com/profile/03258083387204776812noreply@blogger.comtag:blogger.com,1999:blog-2807403883562053852.post-15549327630325674562017-08-10T16:54:47.817-06:002017-08-10T16:54:47.817-06:00You mention a Browning High Power: I recently boug...You mention a Browning High Power: I recently bought a brand-new BHP, simply because I've always wanted one. I did shoot someone else's several years ago, but don't remember much about it. However:<br /><br />At 73 YO, I know I'm not as strong as I once was, and it's even worse because of the hours I sit my fat butt in front of a computer instead of working. But: I can barely rack the slide on my BHP, and actually cannot if the hammer is down. Is something wrong with it, or is it really me? I did manage to shoot 2 mags, loaded to 9 rounds, so I've run 18 shots through it.<br /><br />I have a half-dozen or more M1911s or variants and have no trouble with any of them.<br /><br />Thanks for the cleaning reminder!!<br />jdunmyerhttps://www.blogger.com/profile/09304517693383396419noreply@blogger.com